楔橫軋軋制瞬時轉速的計算機測量和軋制半徑的確定

留言板

尊敬的讀者、作者、審稿人, 關于本刊的投稿、審稿、編輯和出版的任何問題, 您可以本頁添加留言。我們將盡快給您答復。謝謝您的支持!

姓名
郵箱
手機號碼
標題
留言內容
驗證碼

楔橫軋軋制瞬時轉速的計算機測量和軋制半徑的確定

鄭正豪, 蔣家龍

文章導航 > 工程科學學報 > 1992 > 14(3): 333-339

鄭正豪, 蔣家龍. 楔橫軋軋制瞬時轉速的計算機測量和軋制半徑的確定[J]. 工程科學學報, 1992, 14(3): 333-339. doi: 10.13374/j.issn1001-053x.1992.03.025

引用本文:

鄭正豪, 蔣家龍. 楔橫軋軋制瞬時轉速的計算機測量和軋制半徑的確定[J]. 工程科學學報, 1992, 14(3): 333-339. doi: 10.13374/j.issn1001-053x.1992.03.025

Zheng Zhenghao, Jiang Jialong. Computer Measuring of Rolling Rotating Speed and Rolling Radium in Wedge Cross Rolling[J]. Chinese Journal of Engineering, 1992, 14(3): 333-339. doi: 10.13374/j.issn1001-053x.1992.03.025

Citation:

Zheng Zhenghao, Jiang Jialong. Computer Measuring of Rolling Rotating Speed and Rolling Radium in Wedge Cross Rolling[J]. Chinese Journal of Engineering, 1992, 14(3): 333-339. doi: 10.13374/j.issn1001-053x.1992.03.025

鄭正豪, 蔣家龍. 楔橫軋軋制瞬時轉速的計算機測量和軋制半徑的確定[J]. 工程科學學報, 1992, 14(3): 333-339. doi: 10.13374/j.issn1001-053x.1992.03.025

引用本文:

鄭正豪, 蔣家龍. 楔橫軋軋制瞬時轉速的計算機測量和軋制半徑的確定[J]. 工程科學學報, 1992, 14(3): 333-339. doi: 10.13374/j.issn1001-053x.1992.03.025

Zheng Zhenghao, Jiang Jialong. Computer Measuring of Rolling Rotating Speed and Rolling Radium in Wedge Cross Rolling[J]. Chinese Journal of Engineering, 1992, 14(3): 333-339. doi: 10.13374/j.issn1001-053x.1992.03.025

Citation:

Zheng Zhenghao, Jiang Jialong. Computer Measuring of Rolling Rotating Speed and Rolling Radium in Wedge Cross Rolling[J]. Chinese Journal of Engineering, 1992, 14(3): 333-339. doi: 10.13374/j.issn1001-053x.1992.03.025

楔橫軋軋制瞬時轉速的計算機測量和軋制半徑的確定

doi: 10.13374/j.issn1001-053x.1992.03.025

鄭正豪¹,
蔣家龍²

1. 北京鋼鐵設計研究總院;
2. 北京科技大學

計量
- 文章訪問數: 225
- HTML全文瀏覽量: 87
- PDF下載量: 6
- 被引次數: 0
出版歷程
- 收稿日期: 1991-08-22
- 網絡出版日期: 2021-10-16

Computer Measuring of Rolling Rotating Speed and Rolling Radium in Wedge Cross Rolling

Zheng Zhenghao¹,
Jiang Jialong²

1. Beijing Central. Engineering and Reserch Incorporation of Iron and Steel Industry;
2. University of Science and Technology Beijing

摘要: 介紹了用APPLE-Ⅱ微型計算機和光柵脈沖發生器測量楔橫軋軋制轉速和確定軋制半徑的普遍方法,并指出在條件許可的情況下,只要盡量選用高碼道的脈沖發生器就可以提高測量精度。且以某錐體零件毛坯軋制的軋制轉速和軋制半徑測量為例,證明了這一方法是可行的。
- 楔橫軋 /
- 軋制半徑 /
- 滾動半徑
Abstract: This paper introduces a new way that can measure the speed of wedge cross rolling and rolling radium with Apple-Ⅱ computer. It says, the precision of measure can be increased if the precision of equipment is enough. The way is proved to be excellent by measuring the rotating speed and rolling radium of some semifinished spare part as an example.
- wedge cross rolling /
- rolling radium /
- rotating speed of rolling

參考文獻(0)

資源附件(0)

WeChat

點擊查看大圖

計量

文章訪問數: 225
HTML全文瀏覽量: 87
PDF下載量: 6
被引次數: 0

/

下載: 全尺寸圖片幻燈片

分享

用微信掃碼二維碼

分享至好友和朋友圈

返回

中文字幕在线观看