CaAl包芯線的熔化特征及喂線參數的優化

鄭萬; 李天佑; 王春鋒; 熊珊; 李光強; 劉炳宇

doi:10.13374/j.issn2095-9389.2018.s1.024

CaAl包芯線的熔化特征及喂線參數的優化

doi: 10.13374/j.issn2095-9389.2018.s1.024

鄭萬^1,2, ,,
李天佑¹,
王春鋒³,
熊珊¹,
李光強^1,2,
劉炳宇³

1. 武漢科技大學鋼鐵冶金及資源利用省部共建教育部重點實驗室;
2. 武漢科技大學鋼鐵冶金新工藝湖北省重點實驗室;
3. 寶武集團武漢鋼鐵有限公司

基金項目:

武漢科技大學科技創新團隊培育資助項目 (2018TDX08)

詳細信息

通訊作者:
鄭萬, E-mail:zhengwan@wust.edu.cn

中圖分類號: TF769
計量
- 文章訪問數: 40
- HTML全文瀏覽量: 14
- PDF下載量: 2
- 被引次數: 0
出版歷程
- 收稿日期: 2018-02-27
- 網絡出版日期: 2023-07-18

Melting behavior of CaAl cored wire in liquid steel and optimization of wire feeding parameters

1. Key Laboratory for Ferrous Metallurgy and Resources Utilization of Ministry of Education,Wuhan University of Science and Technology;
2. Hubei Provincial Key Laboratory for New Process of Ironmaking and Steelmaking,Wuhan University of Science and Technology;
3. Wuhan Iron and Steel Co.Ltd.,Baowu Group

摘要

摘要: 模擬研究了1873 K鋼液溫度下鋼皮厚度0.74 mm的Ca Al包芯線的熔化、氣化行為及150 t鋼包的理想喂線參數, 并試驗研究了不同鋼種及鈣合金包芯線對鈣收得率的影響.結果表明:包芯線喂入鋼液后, 包芯線的Ca Al合金先于包敷的鋼皮熔化, 自喂入鋼液0.92 s后, 包芯線頂端鋼皮熔化, 液態Ca Al合金進入鋼液后擴散溶解, 當鈣液滴上浮到鋼液面以下1.22 m深度時, 達到了氣化的飽和蒸汽壓, 才會氣化.在150 t鋼包條件下, 為了減少鈣的氣化燒損, 采用3.22⁴.83 m·s^-1的喂線速度, 實現包芯線在鋼液深度2.96 m處熔化的目標.為了提高鈣的收得率, 應采用純鈣包芯線處理碳、硅、錳等元素含量較高的鋼種, 選擇Ca Al包芯線處理低硅低錳的低碳鋼種.
- CaAl包芯線 /
- 鈣處理 /
- 熔化特性 /
- 喂線參數
Abstract: Melting and gasification behavior of Ca Al cored wire with 0.74-mm steel sheet and better feeding process in 1873 K molten steel in 150 t ladle was simulated, and the influence of different Ca cored wire and composition of liquid steel on Ca recovery were analyzed.The results show that calcium alloy of Ca Al cored wire has smelted before its covering steel sheet melts when cored wire is fed into molten steel, melting time of Ca Al cored wire is 0.92 s, then liquid Ca alloy diffuses into liquid steel.Liquid Ca alloy floats upward to 1.22 m below the liquid steel surface and gasifies when alloy has get enough steam pressure of gasification.The feeding speed of 3.22-4.83 m·s^-1for Ca Al cored wire is appropriate to get ideal feeding depth of 2.96 m in ladle with liquid steel.When the elements contents of carbon, silicon and manganese in liquid steel are high, pure Ca cored wire should be used to get bigger Ca recovery, on the contrary, Ca Al cored wire is a better option for low carbon liquid steel with low elements contents of silicon and manganese.
- CaAl cored wire /
- calcium treatment /
- melting characteristics /
- wire-feeding parameters

HTML全文

參考文獻(12)

[1]	Li F, Ren Q, Li Y C, et al. Influence of calcium treatment and protective casting on steel cleanliness during continuous casting process. Steelmaking, 2016, 32 (3) :18 (李菲, 任強, 李雅翀, 等.鈣處理及保護澆鑄工藝對鋼液潔凈度影響.煉鋼, 2016, 32 (3) :18)
[2]	Verma N, Pistorius P C, Fruehan R J, et al. Transient inclusion evolution during modification of alumina inclusions by calcium in liquid steel:Part I. background, experimental techniques and analysis methods. Metall Mater Trans B, 2011, 42 (4) :711
[3]	Yang J, Du J, Chen B T, et al. Influence of calcium treatment on oxide inclusions in ultra-low oxygen refining process. Iron Steel, 2015, 50 (1) :19 (楊俊, 杜江, 陳波濤, 等.超低氧精煉時鈣處理對氧化物夾雜的影響.鋼鐵, 2015, 50 (1) :19)
[4]	Zhang C M, Wang P F, Ai X G, et al. Experimental Method and Device for Simulating Ca Cored Wire Feeding Process in Liquid Steel by Solid Tracer:China Patent, 201610397480. 9. 2016-08-24 (張崇民, 王攀峰, 艾新港, 等.一種采用固體示蹤劑模擬鋼液喂鈣線的實驗方法及裝置:中國專利, 201610397480. 9.2016--08-24)
[5]	Zhang P, Cheng S S, Chen C. Parameter optimization of aluminum wire feeding process during LF refining. J Univ Sci Technol Beijing, 2014, 36 (Suppl 1) :41 (張鵬, 程樹森, 陳川. LF喂鋁線過程參數優化.北京科技大學學報, 2014, 36 (增刊1) :41)
[6]	Huang X H. Metallurgy Principle of Iron and Steel. 4nd Ed. Beijing:Metallurgical Industry Press, 2013 (黃希祜.鋼鐵冶金原理. 4版.北京:冶金工業出版社, 2013)
[7]	Wang H X, Chang G W. Study of wire-feeding velocity during spheroidizing treatment based on ANSYS software. Hot Work Technol, 2011, 40 (11) :52 (王洪新, 常國威.基于ANSYS球化處理時喂線速度的研究.熱加工工藝, 2011, 40 (11) :52)
[8]	Huang H G, Li X M, Yan M, et al. Temperature field simulation on process of calcium cored wire feeding in ladle based on birth and death element method. J Yanshan Univ, 2015, 39 (3) :241 (黃華貴, 李學敏, 燕猛, 等.基于生死單元法的鈣線喂入鋼包過程溫度場仿真研究.燕山大學學報, 2015, 39 (3) :241)
[9]	Liu X K. CFD Simulation and Process Optimization Study of the Process of Metal Core Wire Feeding Ladle[Dissertation]. Qinhuangdao:Yanshan University, 2012 (劉曉凱.金屬芯線喂入鋼包過程CFD數值模擬及工藝優化研究[學位論文].秦皇島:燕山大學, 2012)
[10]	Zhang S T. Research and application of thin wall exhaust pipe of ductile iron spheroidized by feeding alloy cored wire. Heilongjiang Metall, 2014, 34 (5) :50 (張壽濤.喂線球化生產薄壁球鐵排氣管研究與應用.黑龍江冶金, 2014, 34 (5) :50)
[11]	Yan G F, Huang Z Y, Xie Z Q, et al. The oretical discussion on injection speed of cored wire//Proceedings of the 18th National Conference on Steelmaking (2014) . Xi’an, 2014:1 (顏根發, 黃志勇, 謝志強, 等.包芯線喂線速度的理論探討//第十八屆 (2014年) 全國煉鋼學術會議.西安, 2014:1)
[12]	Song B, Han Q Y. Equilibrium of calcium vapor with liquid iron and the interaction of third elements. Metall Mater Trans B, 1998, 29 (2) :415